Is Your Whirlpool Front Load Washer Leaking Water? Follow These DIY Tips
As worrisome as washer leaks can be, many can be fixed with an adjustment, maintenance, or a DIY repair. Wondering why is my Whirlpool front load washer leaking water? Drain hose issues are a common cause. Check the hose for kinks, clogs, or damage that can cause leaking. The following tips can help determine the source of Whirlpool washer leaks and the right solution.
How to Fix a Whirlpool Front Load Washer Leaking Water
After the puddles of water are wiped away, finding the source of washer leaks is the primary priority. Our tips simplify Whirlpool washer troubleshooting with the most likely reasons for leaks.
Need to Adjust Washer Leveling Legs
An unlevel washer can result in excessive vibration during operation, often resulting in a Whirlpool front load washer leaking from door. To lessen vibrations and stop leaks, the washer’s legs can be adjusted to make the washer level with the floor.
Place a carpenter’s level on top of the washer. If it shows that the washer isn’t level, use a wrench to adjust the height of the leveling legs as needed. Make sure each leg is tightly secured to the washer cabinet and has firm contact with the floor.
Kink in Washer Drain Hose
Drain hose issues are one of the most common reasons for a Whirlpool front load washer leaking water. These leaks usually occur behind the washer or at the bottom.
There are several likely causes for drain hose leaks :
- Kinks : A kink can restrict waterflow, creating backups that cause leaks. If the hose is kinked, disconnect it from the washer to gently straighten it.
- Clogs : A clogged drain hose will also cause backups and leaks. Disconnect the drain hose to inspect if for clogs, removing any blockages. If the clog can’t be removed, the hose requires replacement.
- Damage : Holes or cracks in the drain hose will cause leaks. A damaged hose must be replaced.
- Poor connection : Make sure the drain hose is properly installed. The hose must be 39-96″ from the floor to drain properly. It should extend no more than 8″ into the drain pipe and be secure but flexible in its connection.
Washer Leaking From Water Inlet
The water inlet hose allows water to flow to your washer from your home’s water supply. Like the drain hose, Whirlpool front load washer leaking will occur if the inlet hose has holes or cracks, necessitating replacement. If no damage is visible, check the water inlet valve where the hose connects to the washer. While a loose valve can be tightened to resolve leaks, a damaged valve should be professionally replaced.
Whirlpool Washer Drain Filter Needs Cleaning
Wondering why is my Whirlpool front load washer leaking from the bottom. The drain filter may be clogged. Front-load washer maintenance should include regular filter cleanings to prevent clogs and leaks.
Follow these steps to clean a Whirlpool washer drain filter :
- Access the filter by opening the drawer at the bottom of the washer. Release the tabs on either side of the drawer to remove it completely.
- Position a shallow bowl under the drain filter.
- Remove the black hose from its clip, take out the plug, and drain the hose into the bowl. Plug and replace the hose once it’s completely drained.
- Slowly turn the filter counterclockwise and pull it out.
- Remove any visible debris and rinse the filter under warm, running water.
- Replace the filter by rotating it clockwise.
- Realign the drawer on its rails and close, pulling it out again to make sure it’s properly engaged.
Leaky Front Load Washer Door Seal
Also called the gasket or boot, front load vs top load washer has a rubber seal around the front door. This seal provides watertight closure when the door is shut. However, a Whirlpool washer leaking from door suggests that the seal may be compromised.
These factors can cause a leaky washer door seal :
- Dirt : A dirty seal can alter its closure and cause leaks. Wipe down the seal and the glass door with a damp cloth to remove dirt and residue.
- Blockages : Make sure loose clothing or foreign objects aren’t caught in the seal and compromising its closure.
- Damage : Leaks will occur if the seal is loose, ripped, or torn. A damaged seal can’t be repaired and should be professionally replaced.
One of the best ways to keep your washer door seal from leaking is to wipe it down with a clean cloth after each use. This will ensure no debris gets trapped inside and will also help reduce odors from mildew growth.
If your Whirlpool front load washer leaking can’t be resolved with a DIY fix, Reliable Appliance Service can help. Call us for a fast and professional washing machine repair !
Mon - Sun : 24 Hours
Overview